Bitcoin donations to: 1CE9UfWJcHBYkWPns7iqBqZgKhd5xfqEaM thanks!
Buy Bitcoins easily by clicking HERE!


Use coupon radiopreppers for 20% off on the above site.

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Andywragg

Pages: [1] 2 3 ... 6
1
Technical Corner / Re: Digital modes for preparedness
« on: July 11, 2018, 11:02:59 AM »
Take a look at what Julian (OH8STN) is doing with FT-8 using a headless RPii3 and a tablet. You may need a different cable to link to the sound card.

I assume you've got DroidPSK up and running.

2
General Discussion / Re: Have you tried the 160m band?
« on: July 04, 2018, 04:28:34 AM »
OK my 2 bits.....

Not to pour water on your bonfire Gil....

You need double the wire you already need for 80m, you need to lug around another piece of equipment to use the band, to find that when you get there there are very few stations active maybe the occasional submarine  (joke). And the size of the antenna needed means it's more likely to be discovered by any OPFOR/aggressor, and all that comes with that.

From a prepping point of view, I'd be looking to make the most efficient use of the resources I have available, that includes time. It doesn't seem very efficient to try and use a band that most operators either wont consider using or are unable to use.

Is it possible, yes, is it practical/resource efficient, not in my view.

3
Batteries & Solar / Re: 18650 battery testing
« on: July 01, 2018, 05:15:37 PM »
Bit of Video for you...

https://youtu.be/xQvq-7-gAnA

4
Antennas / Re: Linked Dipole
« on: July 01, 2018, 05:09:44 PM »
All being well I'm off to Florida at the end of this month (July) for a couple of weeks of spending money insanely. So, before I leave I'll be having a crafty word with Wolphi and having a Wolphi-Link interface sent to my hotel to save on P&P.

5
Batteries & Solar / Re: 18650 battery testing
« on: July 01, 2018, 12:14:18 PM »
My operation Pack is now assembled. Using 9 cells in a 3S 3P configuration. This should give me an excess of 6A capacity as each cell was over 2200mAH (2240-2280 range). I'm just doing an initial charge to activate the BMS board.

I have made a 3S 1P pack for powering up the uBITX but at the minute this doesnt have a BMS board installed. Video and pics to follow.   

6
General Discussion / Re: Passed my Intermediate Exam last night!!
« on: June 28, 2018, 10:38:14 AM »
Thanks guys - Access to more frequencies, increase ERP from 10 to 50 Watts, and the ability to scratch build and modify stuff. Remote operation within certain limits as well as being able to supervise another licensee on my station.

7
General Discussion / Passed my Intermediate Exam last night!!
« on: June 28, 2018, 04:22:43 AM »
What it says above. Did quite well with the questions, only dropped one out of 45.

Just got to wait 10 days now (for the 6 working day grace period) before I can get my 2E0 or 2E1 callsign, and start to use a bit more power on my QSO's. I can also then complete the TX testing of my uBITX.

Happy Days.


8
Antennas / Re: Linked Dipole
« on: June 28, 2018, 02:56:12 AM »
It's a small world. That linked dipole article was written by one of my club mates.

9
I would have thought the BiTX40 would drop into the uBTX case with the addition of maybe a few different standoff holes.

You could certainly still use the front and rear IO boards with a bit of figuring out for the BiTX40 wiring loom.

Or you could get the uBITX and has access to more bands and increased functionality.


Kerching!!

10
Check this out, and have your wallet ready......

https://youtu.be/Yfhmcili8x0


Since then I have installed the USB cable between the Arduino Nano and the rear IO board, and also fitted the S-Meter sensor, and enabled it in the (KD8CEC 1.08) firmware, although it seems like it's going to take a bit of tweaking to get the bar graph levels 'right'.


11
It's Alive!!!

Check out the FB album and keep an eye on my YT channel. The video compilation is being rendered as I type. Can't TX yet until after next week (hopefully when I pass my intermediate exam) as I've modified the basic kit somewhat.

Really pleased with it so far.

12
Keep checking the Facebook link guys as more progress has been made Today. Only the Mic and audio pot to wire in as standard. Hope to be adding a 6 pin mini din socket for data modes and an S meter sensor.

13
I'm lusting after a Nextion display but it won't work with this case.  I wonder if Sunil has thought about different front plates laid out for different displays.

14
It's arrived and I've made a start.

https://www.facebook.com/andywragg221067/media_set?set=a.10216268867297546.1073741852.1329163645&type=3

Lots of work to do but I'm out with the band tonight so I'm chilling this afternoon.

15
Got the tracking code from Sunil in the last hour. It's on it's way at last. I'll try and post pictures, may be better if I do a video and give you the link here, as I have issues posting pictures for some reason.

Pages: [1] 2 3 ... 6