Bitcoin donations to: 1CE9UfWJcHBYkWPns7iqBqZgKhd5xfqEaM thanks!
Buy Bitcoins easily by clicking HERE!


Use coupon radiopreppers for 20% off on the above site.Become a Patron!

Author Topic: Windom Antenna Analysis With The MR100.  (Read 6011 times)

KQ4BX

  • Newbie
  • *
  • Posts: 1
  • SMeter: +0/-0
    • View Profile
Windom, or OCFD?
« Reply #15 on: November 03, 2018, 08:52:35 PM »
A Windom is another name for the Off Center fed dipole. I have been using one for years, and they are fairly simple to make. My OCFD  gives amazing performance, but that was no accident. I did a lot of research before making an OCFD that worked so well, that many of my friends made one after trying mine.

Some things to know about the OCFED are that the height of the feed point  determines the BALUN needed. The most common BALUN would be a 4:1 current BALUN. The 4:1 works best if the height of the feed point is 35 to 45 feet, or even 50 feet. If you go any higher, the BALUN may need to be adjusted.

The second thing to know, is that ground radials below the antenna, will help tremendously, or i would say they are essential for a well working OCFD.

The ground radials can be place in the ground, just cut a V in the dirt, and place the radial into it and cover it up. The radials should be grounded to your station ground  point. In my case, that is several ground steaks around my tower, and a short connection to the well pipe that is  very close to the tower leg. 

You MUST also connect your home ground to the station ground , if you don't, you will create a dangerous situation for lightening strikes that will hot one ground point, then run through your home toward the next ground point, blowing out everything in between.


Lastly, the 4:1 BALUN I originally made did not work so  well. I was not an expert at making BALUNS, but I followed  directions very well. After a lot of testing and not getting what I considered good performance, I called  BALUN DESIGNS by getting their number off of their website.  I spoke to Bob, and Bob explained a few things to me, and suggested that i try on of his 4:1 BALUNS that was made specifically for an OCFD.   It was rated for 5KW, and had a duel core. Mine was not anything like that.   That BALUN Designs BALUN was the first step in getting an OCFD that worked pretty well. The next improvements came later. one was the height of the feed point went higher, and the next was the ground radials   My OCFD is now amazing, and tunes from 10 to 40m, only skipping 30M. It has flat SWR across 12m, and gives me nice working spots on each band that do not need a tuner. I do use a tuner to widen some of the bigger bands, like 40m. I also can tune to a small section of 75M.  Low low you can go, is alls about the total length of wire you are working with. I work with roughly 45'x90' , but if you have more room, you can double those lengths, and  do much better. My property is not that big.

Wingfoot

  • Newbie
  • *
  • Posts: 1
  • SMeter: +0/-0
    • View Profile
Re: Windom Antenna Analysis With The MR100.
« Reply #16 on: November 10, 2018, 05:37:06 AM »
I have been given an ocfd to try by a friend, it one made by M0CVO it's the HW-40HP model, I've not tried it yet but finding this thread has been helpful & I'll use some of the tips here when installing it, I'll let you know how it goes.

73
Wf

Radio Preppers

Re: Windom Antenna Analysis With The MR100.
« Reply #16 on: November 10, 2018, 05:37:06 AM »