Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - gil

#3091
Technical Corner / I Built an Elecraft K1!
June 12, 2012, 07:08:03 PM
It's alive! After three hair-pulling days, the radio finally works. I received the box on Thursday night; no time then to start, but I got to it after my daily work session on Friday. Late that night, I had completed the filter board, one of the three circuit boards.

I must here explain what an Elecraft K1 is.. Though it sounds like some fighter plane name, it is a receiver/transmitter (a "transceiver") which transmits, and receives CW (Continuous Wave) Aka "Morse Code." It is very small, and covers up to four Ham radio bands. Mine has two, 40 (7Mhz) and 20 meter (14Mhz). The power output is fairly low (7 Watts), but that is sufficient to bounce your signal around the earth.. Imagine seeing a 7 Watts light bulb thousands of miles away! Somehow, it works. CW punches through further than "phone" (voice). The K1 is in a class of radios called "QRP," meaning low power, usually 5 to 10 Watts. It is only sold as a kit, so if you want one, you must build it, or find a used one.. I chose to build it..

I don't understand the fear about winding toroids. I find it very easy and relaxing; it hurts much less than it sounds. All you have to do is count how many times you thread a wire through a ferrite core. How easier can it be? Then, you burn the enamel off the leads with a lighter, clean them up with your snipping tool, and solder.. I was very exited that night about the project. I thought it would be a walk in the park.. Not quite..

The front panel was next. The only difficulty there was soldering the LCD display. Attaching the wires to the ten-turn potentiometer also required some dexterity. About wires.. There are very few in the K1 kit: The potentiometer lead wires, speaker wire, and one coax jumper on the back of the board, that's it. Everything else is connectors. I like that. Soldering wires is always a pain in the butt.

The RF board was the biggest and longest one to build. It took me from around 10-am on Saturday to about 2:30-am on Sunday to complete it! And it didn't work! In retrospect, I should have only completed the receiver part that day, leaving the transmitter for Sunday. When tired, your brain plays tricks on you, and you make mistakes. Everything went fine with the receiver. I heard static when I turned the K1 on, no smoke. After tuning the receiver and plugging-in a long wire, I was listening to CW on both bands. I was exhausted, but proceeded with the transmitter side. It was 9-pm already, eleven hours of looking at tiny components, placing and soldering them.. Then came the time to test voltages on the RF board. Nothing on U8! Shit! Excuse my French.. That wasn't good. I nevertheless plugged-in the filter board to test power output. Nothing.. Followed about an hour of tinkering, swearing, manual-reading, head scratching shenanigans, of which I remember almost nothing (I had been working on it for 15 hours straight). I rewound the bi-filar transformer, reheated solder pads both on the filter and RF boards, zilch! Then I gave up, and decided to complete the build for the heck of it, and call Elecraft in the morning. Yet, after putting the speaker in and closing the box, I tried again. Power on 40m! Not on 20.. Ah.. Back to it (2-am).. I think I transmitted without a dummy load and no antenna a couple times by the way, I was so tired. Anyway, I have no idea what did it, but after countless little troubleshooting steps, and more tuning of the filter board, I finally got output power on both bands. I packed it up and went to bed with a headache and slight twitching..

Comes Sunday morning, I had a working K1! The only peculiar thing left to investigate is some power fluctuation.. If I set the maximum output to 2 Watts, the watt meter shows 2W at first, but then slowly climbs to 2.8. I am guessing that the final transistor produces more gain as it warms up.. I even produced about 10W tuning the filter board before the output suddenly dropped! Weird.. After tuning the filter board on receive, things are a bit more stable, still with quite a power increase as transmit time increases.. It shouldn't occur producing CW though, as this was transmitting a continuous tone in tuning mode. We'll see..

I spent Sunday evening listening to CW outside, with a wire strung horizontally (20ft maybe) about five feet from the ground; the worst possible antenna. Still, it was easy to pick-up signals. I even heard a guy saying he was on a sailboat, and retired three years ago (I have a Morse decoder app on my iPod!).

The Elecraft K1 kit is of very high quality; much better than any other kit I have seen so far (five). Everything fits perfectly, nothing was missing. I even had much needed left-over screws (I spilled them all on the garage floor).. The box looks great, and the way the circuit boards are positioned and fastened is brilliant. I will order the automatic antenna tuner and add it in soon. For now though, I need to finish learning code, then I'll go for the General Ham license (CW is no longer required). The K1 was the right choice, at the right price. You get a lot for your money. It might not seem so when you buy the kit, but after building it, I find it very affordable.

To anyone contemplating building one, go for it! Build a couple kits first, like a Small-Wonder-Labs Rock-Mite, and a SOTA tuner from qrpkits.com, and you'll be well on your way. Moreover, you can test the Elecraft receiver with the Rock-Mite! Get 50ft. of wire from Home Depot for the SOTA tuner, and you'll be all set. Follow the manual EXACTLY. Don't skip ahead, read every line! Double-check everything. Most importantly, don't do what I did. That was stupid. Take your time. If you feel tired or stressed, stop, rest, and don't get back to it until much later. I was very lucky that I didn't fry anything. Not to mention the stress and lack of sleep.. Not a healthy way to spend a week-end..

In the mean time, like they say over there, "Everything is fine in the best of worlds." I am a happy, proud builder and owner of an Elecraft K1. The satisfaction of building something that complex with your own hands is priceless..

#3092
Hello Rich,

I couldn't agree more. I would also rather trust a number of individuals reporting important events rather than some agency.. ARES/RACES probably have the merit of providing a structure and a liaison between disaster relief agencies and the public, but I do not think it is enough. More people with radios, off the grid, is in my opinion the way to obtain and disseminate potentially life-saving information. I am pro-government and pro-law-and-order mind you, but I prefer to be self-sufficient. Many Hams today would probably not be able to use their equipment without power. Others might have very little fuel stored for a generator. A car battery also doesn't last very long.. personally am leaning towards QRP with solar panels.. My newly built K1 draws 55mA on receive...

Thank you for signing up, have a great day,

Gil.
#3093
Net Activity / Re: 6m AM.
June 09, 2012, 11:00:58 AM
Thanks Ray! I didn't know about Echolink... Right now I am learning CW.. I just need to do a couple practice tests for each every day until I get the CW pat down. I am in no hurry, having fun building radio kits right now.

I do want a Yaesu FT-817ND. Like you said, the Gonset is a fun, cool looking radio. I will be changing all the electrolytic capacitors in it, so it gets a new lease on life.. I also bought an MFJ-9406 for a song..

Thanks for registering, even though we only have a few members... Have a great week-end,

Gil.
#3094
After my semi-success with the DC20B, I decided to tackle the Rock-Mite from Small Wonder Labs. I also got the Mighty Box. The kit is very small and has no toroids to wind. It does however have a surface-mounted integrated circuit. Winding toroids is actually very easy. I don't know why people make such a big deal of it. Maybe they just haven't tried. Soldering the SMT circuit, while not that hard, was stressful. That being out of the way, the rest of the kit was a breeze. Being fairly confident of my abilities, I installed the circuit board in the box without trying it first. This way, I could use all the connectors for testing. To my satisfaction, it worked the first time!

My goal with this Rock-Mite is two folds. First, it is a stepping stone to building an Elecraft K1, which I have just started, and second, it provides me with a small emergency radio for my bug-out bag.

I can't really compare the DC20B to the RockMite as far as performance is concerned, but building the Rock-Mite is easier, and there is no tuning required. The circuit board is slightly smaller. I replaced q6 with a 2sc799. R18=2.2 ohms for a little more power. The keyer is the Pico Keyer from http://www.hamgadgets.com.

I am very exited about building the K1. More on that later...

#3095
Technical Corner / Re: RockMite 40m (7030)
June 06, 2012, 10:27:24 PM
Hello,

Mine is in the mail, the 20m version. From your PM, I thought you hadn't built it yet.. I can't wait to start. For anyone new to radio kits, a good way to start is the K12 keyer kit from http://k1el.com or the SOTA tuner from http://qrpkits.com. I am also getting my Elecraft K1 tomorrow! I think I'll like the RM better than the DC20B.. Too finicky to tune.. Have you had any contacts yet? What antenna are you going to use?
#3096
Technical Corner / Elecraft K1 Decision.
June 03, 2012, 02:30:16 PM
I decided to build an Elecraft K1. What the hell is that You might ask.. Though you probably guessed it is a radio. I'm on a roll. I know, I know, I just finished building a small one (DC20B) and am waiting for another tiny transceiver called a Rock-Mite. You need to learn to walk before you can run.. Why not buy something already made? It isn't more expensive.. Well, the Elecraft K1 has an excellent reputation, and it isn't sold assembled. If you want a new one, you must build it. I am good at that stuff, and do enjoy the process. Still, I could find a working Ham radio on Ebay for the same price; but that would be a used item. Not to mention that the K1 is the cutest little radio (did I just say that?).

There is one peculiar thing about this radio, aside from all it's qualities, that is, you can't talk in it.. Morse code only! Also known as "CW" (continuous wave). So I am learning Morse code, and it is far from easy. Why bother? First, a Morse-only transceiver is much simpler and smaller than an SSB (voice) one. It draws less current, which becomes very important when operating on batteries. The K1 will happily work for days on eight AA batteries! For example, a Yaesu FT-817ND draws 450mA on receive. The K1 draws 55mA! More importantly, when propagation conditions are bad, a CW signal will punch through the ether when another mode won't. In an emergency, being heard might be a life-or-death condition. Even with no cell phone coverage and no satellites overhead, there is a good chance the K1 will be heard somewhere, even thousands of miles away. Yes, thousands of miles directly, on eight AA batteries! What else can do that? It doesn't mean I won't take my cell phone or a Spot when hiking far from civilization. However, cell phone coverage is spotty in the North West, and with the Spot, you can't specify the type of emergency, and can only use it for dire situations. If I need anti-venom after a snake bite, it won't do me any good to get picked-up by a helicopter if they don't have the serum with them.. A radio allows you to call for a specific kind of help. Like any other gear, if it is too heavy or too big, you will most likely not take it with you. Light and small is better when you need to carry it on your back.

My plans are to first complete the 20/40m model with no add-ons. Then, I will build the built-in antenna tuner. This option allows you to use a random wire as an antenna without risking frying the transmitter. If you lost your antenna and all you can find is a length of barb wire, the tuner can save your bacon. Just hang it up a tree, press the tuner button, and seconds later, if you're lucky, you will be having a conversation. I might add a noise blanker later.. One item I decided against is the built-in battery pack. You can't charge the batteries while they are inside the case, so what's the point? I heard it is a flimsy add-on anyway. I don't think I'll need more than two bands, but time will tell. The antenna I chose is the Par EF-10/20/40 MkII end-fed dipole. Also on my wish list is a solar panel (PowerFilm AA Battery Solar Panel Charger) to charge those AA rechargeable batteries. For EMP protection, I decided to get some TechProtect Faraday bags.

I will document the build and post it. Average build time is about thirty hours, but I am pretty fast with a soldering iron. I will start next week-end (June 9th), stay tuned for the article, and maybe a video. Hopefully by then I will have learned a few more letters of Morse!

#3097
CB / Re: Galaxy DX 979 CB Radio Review.
May 28, 2012, 12:06:17 AM
I made the modification tonight, replace Q17 with a 2sc2999, and Dl, D2, D30, D31 with 1N6263 Schottky Barrier Diodes. The radio does sound a bit quieter. For ten minutes and less than $2, I'd say it was worth it...

Gil.
#3098
Net Activity / 6m AM.
May 14, 2012, 04:07:58 PM
Hello,

I really would like to organize a 6m AM Net. I have a Gonset Communicator III, and nobody to talk to once I get my license...

Gil.
#3099
The DCxxB from qrpkits.com fits in a box the size of a pack of cigarettes and allows you to make contact all around the world! For $30, how can you go wrong... I thought the best emergency radio is the one you will take with you. The DC20B (there are other bands available) certainly fits that bill. I also ordered a frequency counter kit from N3ZI to help setting it up.

The circuit board it small: 3.5"x2.5". All the components come with the kit, with the exception of plugs needed to mount the PCB in a box. Actually, the kit was missing an integrated circuit socket (I found one at Radio Shack), and had two extra transistors..

It had been a long time (27 years) since I had finished electronics school. I had never soldered on a double-sided circuit board, but it turned out to be fairly easy. I just made sure I had a nice solder joint on both sides. The resistors went in first, then diodes, and so on, mounting the shortest components first, finishing with the talents. This way, you can use a piece of foam to press the components side onto it while you solder on the other side. This keeps the components near the board. One exception is the transistors. You don't want to overheat them, so it is better to mount them a little further out. The final output transistor is not put in until the kit is finished and tuned. Transmitting without a tuned antenna could destroy that component. Winding the coils was a pain. You need to make sure you count the turns carefully. One turn is every time the wire goes through the center. The parts are so small, I needed to wear reading glasses!

When all the components were in, I cut off the plug from old headphones and soldered them in. I also soldered a long wire as an antenna to test reception. It worked! I did hear faint morse code and SSB voices when tuning. The oscillator frequency however seems to be wrong: 14,063.2 Mhz instead of 14,060. I am not sure if there is a problem with the frequency counter, or I am that far off. The morse code keyed works too, so I have a working radio, except for the output frequency. I will need to find someone with an HF ham radio to check my tuning. I am investigating a way to fix the frequency problem and measure it accurately for sure. My progress will be posted here soon, as well as the mounting of the project in a box. Now I just need to learn morse code; darn, why didn't I think of that?

Update (May 27th): I think I am going to ditch the DC20B. I have a box for it, and should complete the build, but after that, it's going away. I can't get it on frequency, and I am not the only one... The Rock-Mite kit should arrive this week. I can't wait to build it. Look for the article!

Update (May 30th): Well, I gave it one last try.. Changed C36 to a 100pF, and C29 to 47pF. It worked! Now I get 14,059.72 on transmit. Receive goes from 14,060.16 to 14,060.32, a perfect 600Hz offset. The problem is the receiver, which has no selectivity. I receive Chinese, French and Spanish commercial radio stations, but little, faint CW signals. Maybe the problem comes from the wire I use as an antenna, which isn't tuned. I will try a tuned dipole during the day and see if I can get clear CW (morse code). I boxed up the DC20B in a nice Hammond cast aluminum box. I made a hole in the cover to tune CT1 and glued a piece of coax outer insulation so that I can't touch anything with my screwdriver upon insertion.. The box is a little big, but it looks good and as though it would survive being run over by a semi-truck.. I might make another hole for access to CT2 and add an RCA plug for a frequency counter (for tuning).

Still waiting for the Rock-Mite (shipped today).
Elecraft K1 arrives tomorrow (June 7th).

#3100
CB / Galaxy DX 979 CB Radio Review.
May 12, 2012, 11:18:32 AM
I wanted a small CB radio with Single Side Band (SSB) that could be used for emergencies. The Galaxy DX 979 seemed to fit the bill. At a mere $140, there wasn't much of a risk. I knew I was getting a cheap radio and did not have high expectations, only a few requirements: Small size, SSB, and perfectly legal. That means forty channels, AM, USB, LSB modes, with 4W max on AM and 12W on SSB (PEP). Not much, but you would be surprised (I was tonight) at how far you can reach with just a few watts, as much power as a small bicycle light bulb!

Most people know the Citizen Band through movies like "Smokey and The Bandit," "Convoy" and others, mostly involving truckers. That is just one side of the coin. The other side are the operators trying to cover the greatest distance possible, and activity called "DX."

CB has a good thing going for itself right now, that is the peak of solar cycle 24. Propagation is going to be very good for probably another couple years. Radio waves in the 11m (27Mhz) band do bounce off the ionosphere when conditions are right. SSB being excellent at receiving weak signals, you have a very good chance to skip pretty far.

The Galaxy is cheaply made (compared to a Yaesu HAM radio of similar price). The buttons on the front panel are "chromed" plastic and look cheesy. The whole radio looks and feels cheap. I even had a very hard time putting in the mounting bracket screws. I had to tighten them with a pair of pliers and was lucky not to strip any thread. Looking inside the box gave me the same feeling. I like the big meter and the fact that you can dim the blue LEDs.

I connected the transceiver to my Solarcon Max2000, a 24ft. antenna mounted about 15ft off the ground, surrounded by trees, and an Astron power supply. Good thinking from Galaxy for putting the microphone plug on the front panel by the way, which I plugged in, then turned the volume knob to ON. It worked! I shouldn't be so negative, since I suspect that most CB radio manufacturers produce the same lever of "quality." I tuned to 38LSB and listened, playing with the clarifier whenever I heard someone calling DX.

[tip]The clarifier is the knob that turns the "Donald Duck" voices you hear on SSB into something you can understand.[/tip]

If you are a safe cracker by trade, you won't have any trouble with the clarifier on the 979. It takes that kind of finger dexterity to operate the darn thing. Before you have a caller "clarified," he is usually done talking.. Aggravating.. The range on the clarifier is too broad. My old President Jackson has a much better clarifier, but of course, that radio has acquired a quasi legendary status in the CB world. With a little practice, you get better at it, but geez!

Compared to HAM transceivers, CBs are noisy... I plan on replacing a few diodes with Schottky Barrier Diodes, and replace an RF amp transistor with a 2sc2999, High Gain, Low Noise model. The procedure is described here; part are on the way (about $1.60!).

I remembered that I should check the SWR before transmitting, which was a perfect opportunity to test the inboard SWR meter. I also plugged in a Workman el-cheapo meter on the antenna output. They did not agree with each other! The Galaxy SWR meter barely moved while the workman showed 1:1.8! I tuned the antenna and got down to 1.6 (probably all those trees..). Oh well. Just keep an eye on the SWR warning LED.. It works (I had a short in one plug); the SWR meter also jumped up. It might not be the most sensitive SWR meter, but it will let you know when you risk frying your final transistors.

It was getting late and the band was dying down when I heard "476" calling. He did not say where he was from, but I could hear him very well, good audio and a signal of 7. I expected him to be within fifty miles of me. I asked him about his location and he said "Jamaica!" I had a low signal but good audio (mike gain turned all the way up). Not bad for a $140 piece of gear. The antenna is everything, mind you, and the IMax2000 did it's part. The Galaxy... I hadn't wasted my money..

The Galaxy DX 979 won't win manufacturing quality contests. It does however work well. For the price, you can buy two and box one up in an ammo can for EMP protection. It is a small price for never being entirely cut off from the rest of the world.

#3101
Antennas / Building a 2m Slim Jim Antenna.
May 09, 2012, 03:41:07 PM
I needed a better antenna for my Yaesu FT-270R. My requirements were to find a portable, efficient and easy to build design. The short rubber antenna works fine for me now, especially that I am not transmitting before getting my license. I do want more range however for emergency situations, in case local repeaters are down. My first thought was to make a Yagi-Uda directional antenna. They have a high gain but transmit in only one direction. While this can be an advantage, and I plan on getting one, my go-to antenna needs to be omnidirectional. I found the Slim Jim design to be my best option. It is easily made from soldered copper tubing. All you need is a couple of 5ft lengths of 1/2" tubing, 90deg corners, end caps and PVC Ts. I added an electrical junction box for the feed-point connector, but it might make it more difficult to attach the coax and tune the antenna.

Total length very-top to very-bottom is 58". Width center-to-center is 2". Gap is about 1-3/4". See the Ham-Universe articles (1 & 2) for exact measurements.

It is easy to calculate dimensions for other frequencies:

  • 3/4w : 8415/F-mhz.
  • 1/2w : 5610/F-mhz.
  • 1/4w : 2805/F-mhz.
  • Feed point : 10-20% of 1/4w.

The gap is taken off the 1/4 wave element...

Slim Jim Gap

The PVC Ts need to be reamed with a 5/8" drill bit so that the copper tubing can go through. I used a bit of WD40 to slide them down. Between the two Ts, I epoxied a 1" piece of 1/2" plastic tubing. There is one "H" PVC support assembly on the top portion and one on the lower portion, right next to the end cap.

Slim Jim Feed Point

I am not sure that using a plastic electrical junction box was a good idea for the feed point. Since I have not received my SO-239 socket yet, I must hold off on the electrical connection. My concern is that soldering will be difficult without burning the plastic box. I might have to use sheet-metal screws. Tunig might not be easy either, since the best SWR is obtained by moving the feed point up and down, between 3 and 4" from the very-bottom. Maybe I should have used PVC Ts, like for the two support "H" assemblies. They can be split in half, then the coax soldered after finding the best feed point. Once epoxied, it would look fine. I do like the look of my electrical box though, and if it works fine, I will be happy with the results.

Total building time was about an hour. Everything came from the hardware store, except the SO-239 connector. Soldering turned out to be pretty easy. I sanded the parts and used flux paste before heating up the assembled parts with a torch. Once the parts are hot enough, you put the solder on, which flows in the joint, following the flux. Cost could have been as low as $30, but I spent about twice that much, not counting tools (hacksaw, drill bit, epoxy, solder), which you might have already. If you are starting "empty handed," plan on $100. While it can cost more than a factory-made antenna, you get the satisfaction of building something yourself, which might be actually sturdier than a store-bought model.

Stay tuned for the finishing touches (painting), electrical connection and reception testing.

Thanks to Richard KE5FXU SK at hamuniverse.com for the article!

Update, April 11th:

Finally, I got my SO-239 plug. Drilling the PVC box was easy. I didn't even use my drill press. It only took me a few minutes by hand! Holes are one 5/8" in the middle, and four 1/8" around. I drilled in the middle of the lid, hoping I would have enough leeway to adjust the SWR by moving the contact in the box along the tube. First, as I suspected, I could not get the tube hot enough to solder the center of the coax to the copper tube using my 30w soldering iron. I solved the problem by heating up the tube with a Zippo under it while I soldered on top! It worked really well. I did the same to put soldering points in the box, every quarter inch or so. The zippo was placed an inch from the box. I was worried about melting it, but these electrical boxes are pretty heat-resistant. Sorry about picture quality:

Solder Points

It's a bit ugly, but inside the box anyway..

Feed Box

Reception works great. I was able to listen to a conversation tonight on a distant repeater that I simply could not hear with the HT rubber antenna. I get three extra signal bars with the Slim Jim. I got a cheap VHF/UHF digital SWR meter from Hong-Kong, which seems to work fine, but for the connectors which are of "N" type.

Digital SWR meter

Update, May 1st:

I painted the antenna sort of a flat olive-drab color for stealth. I can easily hoist it up a tree and it blends in very well. SWR varies from 2.4:1 on the lower part of the band, to 1.8:1 around 146Mhz, and remains around 1.4:1-1.5:1 from 146.5 up. I used a ferrite RF choke kit from Palomar Engineers (photo below), which got the SWR down to 1.36:1 around 147.5Mhz. I much prefer the ferrite choke to the coax balun type, which looks ugly and wastes cable.

Slim Jim Connection Box With Palomar Ferrite Choke
 
What I like the most about the Slim Jim is it's sturdiness and that given it's shape, you can hang it from anywhere, as long as you use an isolator to do so. When hanging it, I plug in an "L" shaped adaptor (photo above) to avoid bending the coax.


Update Oct 30, 2012: I have been using the antenna with my Icom IC-271A and it works great, even with the antenna set on the corner of my desk! I do plan on putting it outside on a pole or hoisted in a tree, but haven't had the time. I can hit distant repeaters on half-power (13W) with no problem and get good reports. What I like most about it is that I can take it with me anywhere and not worry about banging it or damaging it. It is easy to hoist up with a string or tape it to a pole. The SWR can probably be reduced by doing a better job at finding the sweet spot to attach the coax. It doesn't even look like an antenna to the untrained eye, which is always a plus.
#3102
I bought my first CB radio in 1984, a Lafayette LM300. I wish I still had it. Ten years later I got a President Jackson. After CB went ?down the drain,? I stopped all radio activity, until today.

I clearly remember twenty years ago, even five. I did not then have any of the concerns I have today. The future was bright with no clouds on the horizon. I don?t think the world is going to end this December twenty first, or next year for that matter. The Mayan who wrote his calendar must have been tired that night, and his wife was complaining about how much time he spent on it, so he probably just thought it went far enough and left it at that.. I am no doomsday preacher.
There is a certain unease among us however. The media is broadcasting multiple disaster and prepping shows. The economy isn?t going better. Five years ago, I had five ounces of gold, bought for less than $1500. Today, those coins would be worth close to $10,000. Only five years later! I am still hitting myself on the head for selling them before the increase. We may wonder why the value of the Dollar and the Euo have not gone down by a factor of six or seven. One only has to watch the news to start worrying.

I have always been the poster child for safety. Yet, I have enjoyed dangerous activities like ultralight flying, cave diving, motorcycle riding, parachute jumping and others, but always prepared and trained properly. The fact that I am here today has nothing to do with chance.

Being prepared for me means being prepared in all areas. I have seen people stocking up food while smoking two packs a day, shooters with dozens of guns who can't run to their 100yrd target, or people with a bunch of medical supplies but no water or any means to purify it. I have seen very few preppers with the means to communicate!

So, I am studying for my HAM licenses (yes, all of them), while enjoying my Galaxy DX 979 CB.

I have thought about HAM bands quite extensively and done a lot of research with an emphasis on emergency use.

For local communications, 2m seems the best option. I would also include a few FRS handhelds to keep track of family members and local friends in your neighborhood. I can't think of anything the 70cm band offers that 2m can't do.

A CB is a must as well, but it should include SSB, to take advantage of the 11m band's ability to skip on the ionosphere, thus allowing very long distances.

I am also intrigued by the 6m band, which at times behaves either like VHF or HF, depending on conditions. It also has the advantage of small antennas, with a half-wave being, well, 3m long! I found an old 6m Gonset Communicator III AM radio on Ebay for cheap, with a crystal for 50.4mhz. That set would probably survive an EMP sitting right in the open! If only someone else around had one...! 6m AM would make a great local frequency, if small and cheap handhelds were available. You would also get skip when the conditions are exceptionally good.

On HF, I am planning on sticking to 20m (14mhz). Lower than that and you run into antenna length problems. You can find cheap QRP kits for that band. I have ordered a small CW only transceiver kit for $30! How can you beat that? 20M is probably the most popular HAM band and would be great to listen to in a national emergency. Moreover, propagation is decent to great most of the time during the day and early evening hours.

In my opinion, better have a few radios for different bands rather than one that covers them all. I do want a Yaesu FT-817ND, but I will have a metal can with a 2m handheld, CB, 6m SSB, 20m QRP transceiver, a handful of FRS handhelds and a few accessories stored inside a cardboard box inside the can, for EMP and water protection. For a few hundred dollars, you can be well prepared as far as radios go. Much less than the cost of a good rifle ;-)
#3103
Information is a vital commodity in a disaster situation. Whomever has any, in the absence of Internet, phone and power services will have a great advantage.

Radio Preppers aims to provide individuals interested in disaster preparedness with an independent tool for the exchange of information about emergency radio communications and preparations. Hopefully it will also help build a community of like-minded individuals who could contact and help each others in times of what is commonly known as 'SHTF' or 'TEOTWAWKI.' Like-minded here means self-sufficient, strong-willed and responsible people. Independent means regardless of nationality, race, gender, political and religious beliefs, as well as unrelated to any organizations. Whether you are a licensed HAM operator, CBer, or simply curious about radio preparedness doesn't matter here.

My motivation for creating this site came from my inability to find an emergency radio club that really wasn't related to some kind of organization, mostly governmental or politically affiliated. Survival is a personal, family or small community affair. I am always suspicious of organizations that plan on telling people what to do for their own good, or else... That said, anti-government rhetoric will not be accepted here. If you don't like your government, vote accordingly. There are plenty of other boads for political ranting. This one is not one of them.

Sign-up, it's free, and stop by once in a while. If you have anything to contribute, please do so! Topics will not necessarily be limited to radio but must be related to disaster preparedness. To avoid spamming, you do need to answer a couple radio related questions; nothing a quick Google search can't answer.

Rules are few: Be courteous. Although some civil political discussions are acceptable, try to avoid them; same goes for religion. Do not suggest anything against the law, or you will be immediately banned.

Please consider supporting this site after joining by subscribing at: Profile > Summary > Actions > Paid Subscriptions. You will get more privileges!

Note that members who do not participate at least once a year will be deleted.

Any suggestions would be appreciated. I hope you enjoy this forum and that it helps make you and your family safer.

Gil.